MPNbase

80×140×26 mm bearings

43 models from 3 brands across 4 types share this ISO 15 envelope: 80 mm bore, 140 mm outside diameter, 26 mm width (3.150×5.512×1.024 in), 30 mm radial section.

43 models fit this space 3 brands 43 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
1216 Self-Aligning Ball NTN open — 40 17 1680
1216-K Self-Aligning Ball SKF open CN 39.7 17 1650
1216K Self-Aligning Ball NTN open — 40 17 1680
216 Deep Groove Ball SKF open CN 88 85 1550
216-ZZ Deep Groove Ball SKF ZZ CN 88 85 1550
6216 Deep Groove Ball SKF open CN 72.8 55 1450
6216-2RS Deep Groove Ball SKF 2RS CN 72.8 55 1500
6216-2RS-NSK Deep Groove Ball NSK 2RS CN 80 53 1420
6216-2RS-NTN Deep Groove Ball NTN 2RS CN 80.5 53 1400
6216-M Deep Groove Ball SKF open CN 72.8 55 1700
6216-NSK Deep Groove Ball NSK open CN 80 53 1420
6216-NTN Deep Groove Ball NTN open CN 80.5 53 1400
6216-RSR Deep Groove Ball NSK RSR CN 80 53 1420
6216-RSR-NTN Deep Groove Ball NTN RSR CN 80.5 53 1400
6216-ZZ Deep Groove Ball SKF ZZ CN 72.8 55 1550
6216-ZZ-NSK Deep Groove Ball NSK ZZ CN 80 53 1420
6216-ZZ-NTN Deep Groove Ball NTN ZZ CN 80.5 53 1400
7216 Angular Contact Ball SKF open CN 80.6 69.5 1450
7216-BECBM Angular Contact Ball SKF open CN 85 75 1450
7216-BECBP Angular Contact Ball SKF open CN 85 75 1450
7216-BECBPH Angular Contact Ball SKF open CN 85 75 1450
7216-BECBY Angular Contact Ball SKF open CN 85 75 1450
7216-BEGAPH Angular Contact Ball SKF open CN 85 75 1450
7216-BEP Angular Contact Ball SKF open CN 80.6 69.5 1450
7216-NTN Angular Contact Ball NTN open CN 98.5 76 1390
7216B Angular Contact Ball NTN open CN 89 69.5 1420
N216 Cylindrical Roller NTN open CN 118 122 1470
N216-ECP Cylindrical Roller SKF open CN 160 166 1550
N216EA Cylindrical Roller NTN open CN 165 167 1560
NF216 Cylindrical Roller NTN open CN 118 122 1470
NF216EA Cylindrical Roller NTN open CN 165 167 1560
NJ216 Cylindrical Roller NTN open CN 118 122 1470
NJ216-ECP Cylindrical Roller SKF open CN 160 166 1550
NJ216EA Cylindrical Roller NTN open CN 165 167 1560
NU216 Cylindrical Roller SKF open CN 160 166 1550
NU216-NTN Cylindrical Roller NTN open CN 118 122 1470
NU216EA Cylindrical Roller NTN open CN 165 167 1560
NUP216 Cylindrical Roller NTN open CN 118 122 1470
NUP216-ECP Cylindrical Roller SKF open CN 160 166 1550
NUP216EA Cylindrical Roller NTN open CN 165 167 1560
QJ-216-MA Angular Contact Ball SKF open CN 146 156 1850
QJ-216-N2MA Angular Contact Ball SKF open CN 146 156 1850
QJ216 Angular Contact Ball NTN open CN 124 217 1830

Note: catalogue dynamic load ratings for this envelope span 39.7– 165.0 kN — a 316% spread between designs in the very same 80×140×26 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 80 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 1216, 1216-K, 1216K, 216, 216-ZZ, 6216, 6216-2RS, 6216-2RS-NSK, 6216-2RS-NTN, 6216-M, 6216-NSK, 6216-NTN, 6216-RSR, 6216-RSR-NTN, 6216-ZZ, 6216-ZZ-NSK, 6216-ZZ-NTN, 7216, 7216-BECBM, 7216-BECBP, 7216-BECBPH, 7216-BECBY, 7216-BEGAPH, 7216-BEP, 7216-NTN, 7216B, N216, N216-ECP, N216EA, NF216, NF216EA, NJ216, NJ216-ECP, NJ216EA, NU216, NU216-NTN, NU216EA, NUP216, NUP216-ECP, NUP216EA, QJ-216-MA, QJ-216-N2MA, QJ216.

Frequently asked questions

Are all 80×140×26 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 80 mm bore, 140 mm OD, 26 mm width (3.150×5.512×1.024 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 43 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 80×140×26?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 80×140×26 mm in inches?

80×140×26 mm converts to 3.150×5.512×1.024 in, with a 30 mm (1.181 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 1216, 1216-K, 1216K mount in the same space despite different internal designs.