6222-2RS-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6222-2RS-NTN model number is decoded

6222-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 22 by five gives the 110 mm bore; the 200 mm outside diameter and 38 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 110 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's contact-seal catalogue number is 6222LLU (suffix LLU, or LLH low-torque variant), mapped here from the industry-neutral -2RS spelling; the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 110 mm bore the ring mass is significant: heat 6222 on an induction heater (max 120 °C), never over an open flame, and plan puller access or a withdrawal sleeve now for the day it has to come off again.
• The 62xx light series is the default general-purpose section at 110 mm bore; before upgrading to a 6322 for extra capacity, confirm the housing accepts a 200 mm OD and 38 mm width — it is not a drop-in swap.
• Heat is the enemy of the sealed 6222-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 6222-2RS-NTN in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 6200-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• NTN catalogues the contact-sealed version as 6222LLU (suffix LLU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.
• At 110 mm bore 6222 is in NTN's medium industrial range; the pressed-steel cage is standard but large-section 63xx/64xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 2200 r/min for 6222; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 160 kN dynamic load rating (C) and 117 kN static (C0), 7.35 kN fatigue load limit Cu, 6222 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 4360 g (4.4 kg), 6222 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 110×200×38 mm envelope of 6222 gives a D/d ratio of 1.82 and 45.0 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 160/117 kN load ratings, 7.35 kN fatigue load limit Cu NTN lists the grease limiting speed at 2200 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 4360 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6222LLU on the 110×200×38 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6222 in a rated drive.
• Standard catalogue stock of 6222 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.