MPNbase

110×200×38 mm bearings

35 models from 3 brands across 4 types share this ISO 15 envelope: 110 mm bore, 200 mm outside diameter, 38 mm width (4.331×7.874×1.496 in), 45 mm radial section.

35 models fit this space 3 brands 35 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
1222 Self-Aligning Ball NTN open — 87 38.5 5210
1222-K Self-Aligning Ball SKF open CN 88.4 39 5150
1222K Self-Aligning Ball NTN open — 87 38.5 5210
6222 Deep Groove Ball SKF open CN 151 118 4450
6222-2RS Deep Groove Ball SKF 2RS CN 151 118 4600
6222-2RS-NSK Deep Groove Ball NSK 2RS CN 159 117 4450
6222-2RS-NTN Deep Groove Ball NTN 2RS CN 160 117 4360
6222-NSK Deep Groove Ball NSK open CN 159 117 4450
6222-NTN Deep Groove Ball NTN open CN 160 117 4360
6222-RSR Deep Groove Ball NSK RSR CN 159 117 4450
6222-RSR-NTN Deep Groove Ball NTN RSR CN 160 117 4360
6222-ZZ Deep Groove Ball SKF ZZ CN 151 118 4600
6222-ZZ-NSK Deep Groove Ball NSK ZZ CN 159 117 4450
6222-ZZ-NTN Deep Groove Ball NTN ZZ CN 160 117 4360
7222 Angular Contact Ball SKF open CN 153 143 4600
7222-BECBM Angular Contact Ball SKF open CN 163 156 4600
7222-BECBP Angular Contact Ball SKF open CN 163 156 4600
7222-BECBY Angular Contact Ball SKF open CN 163 156 4600
7222-BEP Angular Contact Ball SKF open CN 153 143 4600
7222-NTN Angular Contact Ball NTN open CN 188 158 4450
7222B Angular Contact Ball NTN open CN 170 144 4540
N222 Cylindrical Roller NTN open CN 266 290 4540
N222-ECP Cylindrical Roller SKF open CN 335 365 4800
NF222 Cylindrical Roller NTN open CN 266 290 4540
NJ222 Cylindrical Roller NTN open CN 266 290 4540
NJ222-ECP Cylindrical Roller SKF open CN 335 365 4800
NJ222E Cylindrical Roller NTN open CN 325 365 —
NU222 Cylindrical Roller NTN open CN 266 290 4540
NU222-ECP Cylindrical Roller SKF open CN 335 365 4700
NU222E Cylindrical Roller NTN open CN 325 365 —
NUP222 Cylindrical Roller NTN open CN 266 290 4540
NUP222-ECP Cylindrical Roller SKF open CN 335 365 5000
NUP222E Cylindrical Roller NTN open CN 325 365 —
QJ-222-N2MA Angular Contact Ball SKF open CN 280 325 5600
QJ222 Angular Contact Ball NTN open CN 236 450 5620

Note: catalogue dynamic load ratings for this envelope span 87.0– 335.0 kN — a 285% spread between designs in the very same 110×200×38 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 110 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 1222, 1222-K, 1222K, 6222, 6222-2RS, 6222-2RS-NSK, 6222-2RS-NTN, 6222-NSK, 6222-NTN, 6222-RSR, 6222-RSR-NTN, 6222-ZZ, 6222-ZZ-NSK, 6222-ZZ-NTN, 7222, 7222-BECBM, 7222-BECBP, 7222-BECBY, 7222-BEP, 7222-NTN, 7222B, N222, N222-ECP, NF222, NJ222, NJ222-ECP, NJ222E, NU222, NU222-ECP, NU222E, NUP222, NUP222-ECP, NUP222E, QJ-222-N2MA, QJ222.

Frequently asked questions

Are all 110×200×38 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 110 mm bore, 200 mm OD, 38 mm width (4.331×7.874×1.496 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 35 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 110×200×38?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 110×200×38 mm in inches?

110×200×38 mm converts to 4.331×7.874×1.496 in, with a 45 mm (1.772 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 1222, 1222-K, 1222K mount in the same space despite different internal designs.