61807-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61807-FAG model number is decoded

In the 61800-series (diameter series 8 of ISO 15) the last two digits encode the bore: 61807 carries bore code 07 = 35 mm. Outside diameter 47 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 35 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 35 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 61807-FAG.
• Only 6.0 mm of radial section separates bore and OD on the 618xx series at 35 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6207.
• Storage matters for open bearings: 61807-FAG leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61807 units.
• Do not quieten a noisy bearing by preloading it: the 61800-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 61807-FAG-C3. No clearance suffix means normal CN clearance.
• The open 61807 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• FAG rates 61807 at 21600 r/min mechanical limiting speed (thermal reference speed 9900 r/min) — a high-speed range where the thermal reference speed governs continuous duty; use low-viscosity turbine oil or high-speed grease and avoid lip-contact seals entirely.
• The 35 mm bore puts 61807 in Schaeffler's general-purpose industrial range; the standard cage and CN clearance cover most electric-motor and pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• At 4.74 kN dynamic load rating (C) and 3.82 kN static (C0), 61807 is a light-load FAG bearing: L10 life above a few kN of equivalent load is short, so size up to a 62-series on the same bore if the duty sees shock or frequent starts.
• At only 32 g, 61807 is a lightweight FAG bearing that can be handled by hand; still press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 35×47×7 mm envelope of 61807 gives a D/d ratio of 1.34 and only 6.0 mm radial section height — an ultra-thin section in the HR 1 range where shaft deflection and housing ovality load the ball-raceway contact directly; verify shaft stiffness (target deflection under 0.05 mm) before choosing it over a 62-series.
• The 4.74/3.82 kN load ratings, mass 32 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 61807-FAG on the 35×47×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61807 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• For hot shafts above roughly 100 °C continuous, consult Schaeffler about seal material and grease options for the 2RSR execution of 61807; the standard NBR lip is the economical general-duty choice, not the high-temperature one.
• Schaeffler's medias/eKatalog is the live source for the current execution of 61807: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.