61807-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61807-RSR-NTN model number is decoded

In the 61800-series (diameter series 8 of ISO 15) the last two digits encode the bore: 61807 carries bore code 07 = 35 mm. Outside diameter 47 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 35 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6807JRLLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 35 mm shaft for 61807 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• The 618xx thin section at 35 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6207.
• RSR low-friction seals on 61807-RSR-NTN run faster than contact-seal 61807-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61807-2RS instead.
• The non-contact lip of 61807-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 35 mm bore position before relying on it as sealed-for-life.
• Do not quieten a noisy bearing by preloading it: the 61800-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Shaft and housing fillets must clear the bearing chamfer so the 7 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• NTN catalogues this low-friction non-contact seal as 6807JRLLB (suffix RLLB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• The 35 mm bore puts 61807 in NTN's general-purpose industrial range; the standard pressed-steel cage and CN clearance cover most electric-motor and pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• NTN rates 61807 at 13000 r/min grease limiting speed — this is an electric-motor range; keep the grease fill at 25–35% of the free bearing volume and avoid mixing grease thickener types if regreasing through the seal lip.
• NTN rates 61807 at 5.45 kN dynamic (C) and 4.05 kN static (C0), 0.27 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At only 29 g, 61807 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 35×47×7 mm envelope of 61807 gives a D/d ratio of 1.34 and only 6.0 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 5.45/4.05 kN load ratings, 0.27 kN fatigue load limit Cu NTN lists the grease limiting speed at 13000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 29 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6807JRLLB on the 35×47×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61807 in a rated drive.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61807 is listed.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.