61902-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61902-NSK model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61902 carries bore code 15 = 15 mm. Outside diameter 28 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 15 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 15 mm bore, induction heating to roughly 80–100 °C is the clean mounting method; never exceed 120 °C, and hold 61902 against the shaft shoulder while it cools so the ring cannot creep back.
• The 619xx thin section (6.5 mm section height at 15 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• The open 61902-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 15×28×7 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61900-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61902 units.
• Measure the shaft, do not trust the drawing: a 15 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61902-NSK.
• Do not quieten a noisy bearing by preloading it: the 61900-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 61902 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• At 15 mm bore the 61902 sits in NSK's small-bore range; NSK ships these sizes with a pressed-steel cage and P0 tolerance as standard, and NSK's EA (extra-precision) or P5 class is a special-order upgrade for spindle duty — do not assume catalogue P0 figures hold for instrument use without an NSK engineering check.
• At 4.75 kN dynamic load rating (C) and 2.26 kN static (C0), 61902 is a light-load NSK bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 15 g, 61902 is a lightweight NSK bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×28×7 mm envelope of 61902 gives a D/d ratio of 1.87 and 6.5 mm radial section height — a standard NSK medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to NSK's listed speed ratings, and C3 clearance is the common choice for hot shafts.
• The 4.75/2.26 kN load ratings, mass 15 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6902 on the 15×28×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61902 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 61902; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.