61902-RSR bearing: complete specifications & equivalents
The 61902-RSR is a ISO 15 radial bearing sized 15 x 28 x 7 mm (bore x OD x width) with RSR sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 15 mm |
| Outer diameter D | 28 mm |
| Width B | 7 mm |
| Material | GCr15 |
| Seal / shield | RSR |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 4.36 kN |
| Basic static load rating C0 | 2.24 kN |
| Fatigue load limit Pu | 0.095 kN |
| Reference speed (thermal) | 56000 rpm |
| Limiting speed (mechanical) | 28000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 16 g |
| Manufacturer designation | SKF 61902-2RZ |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 0.591 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.276 in |
| ISO bore code | 02 |
| Radial section height (D−d)/2 | 6.5 mm |
| Smallest bore in 61900-series | 3 mm |
| Largest outer diameter in 61900-series | 1120 mm |
| Width range across 61900-series | 3–118 mm |
| Bore position in 61900-series (smallest first) | 10 of 63 |
| Bore above smallest 61900-series size | 12 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61902-2RS-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant differs (RSR vs 2RS) — confirm sealing suits the duty. |
| 61902-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant differs (RSR vs OPEN) — confirm sealing suits the duty. |
| 61902-ZZ-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant differs (RSR vs ZZ) — confirm sealing suits the duty. |
| 61902 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting. |
| 61902-2RS-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant differs (RSR vs 2RS) — confirm sealing suits the duty. |
| 61902-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant differs (RSR vs OPEN) — confirm sealing suits the duty. |
| 61902-RSR-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 61902-ZZ-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant differs (RSR vs ZZ) — confirm sealing suits the duty. |
| 61902-2RS-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant (RSR vs 2RS) and load ratings differ — confirm sealing and rating before substituting. |
| 61902-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting. |
| 61902-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 61902-ZZ-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 15×28×7 mm envelope per ISO 15; seal variant (RSR vs ZZ) and load ratings differ — confirm sealing and rating before substituting. |
| W61902-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 61902-2RS1 shares the 15×28×7 mm envelope but rates differently (4.36/2.24 kN vs 3.71/2.24 kN) — not a load-rating equivalent. |
| W61902-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 61902-2Z shares the 15×28×7 mm envelope but rates differently (4.36/2.24 kN vs 3.71/2.24 kN) — not a load-rating equivalent. |
| W61902 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 61902 shares the 15×28×7 mm envelope but rates differently (4.36/2.24 kN vs 3.71/2.24 kN) — not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61902-RSR model number is decoded
61902-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the thin 619xx section (diameter series 9 of ISO 15), its bore code 02 comes from the 10/12/15/17 mm exception table, giving a 15 mm bore; the 28 mm outside diameter and 7 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. SKF's low-friction seal suffix is 2RSL/2RZ (this page's industry-neutral spelling is -RSR); catalogue number 61902-2RZ.
Typical equipment & failure modes
Common applications
- space-constrained gearboxes
- clutch and transmission assemblies
- robotics and automation joints
- lay shafts and idler shafts
Known failure patterns
- ingress of fine dust or moisture past the non-contact lip in dirty or wet duty (RSR is not liquid-tight)
- lip-lubricant starvation if the bearing runs dry for extended periods
- fretting corrosion on a loose shaft seat
- cage damage from operation beyond the limiting speed
Selection pitfalls — read before you substitute
- Bore codes 00–03 use the exception table: 61902 fits a 15 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).
- The 619xx thin section at 15 mm bore (6.5 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
- RSR low-friction seals on 61902-RSR run faster than contact-seal 61902-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61902-2RS instead.
- The non-contact lip of 61902-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 15 mm bore position before relying on it as sealed-for-life.
- Measure the shaft, do not trust the drawing: a 15 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61902-RSR.
- A 15 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
- SKF catalogues the low-friction seal as 61902-2RZ (suffix -2RSL or -2RZ): a non-contact elastomer lip that runs near the open 28000 r/min limiting speed, closer to the open bearing's 56000 r/min reference than the contact-seal version. It keeps coarse debris out without the drag of a contact seal, but is not liquid-tight — use 2RSH for wet or fine-dust positions.
- The 4.36/2.24 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61902-RSR bearing?
A 61902-RSR deep-groove ball bearing has a 15 mm bore, 28 mm outer diameter and 7 mm width (0.591 × 1.102 × 0.276 in), per ISO 15 boundary dimensions. It is fitted with two low-friction non-contact rubber seals.
Are 61902 bearings from different brands interchangeable?
For boundary dimensions, yes: every brand's 61902 uses the same ISO 15 envelope (15×28×7 mm). Load ratings, limiting speeds, clearance, precision class and sealing design can differ, so verify those in the supplier catalogue when substituting. Seal suffixes also differ by brand (2RS, DDU, LLU, 2RSL and similar).
What internal clearance does 61902-RSR have?
Unless a clearance suffix says otherwise, 61902-RSR is manufactured to normal (CN) radial internal clearance. Tight fits and hot shafts consume clearance in service — for those conditions order the C3 execution of 61902 and verify the residual clearance after mounting.
How should 61902-RSR be mounted?
Apply the mounting force to the ring being fitted: on a 15 mm shaft seat the press load must pass through the inner-ring face only. A fitting sleeve and an arbor press are normally sufficient at this size. Never strike the outer ring, the cage or the seals.
What is the SKF designation and catalogue data for 61902-RSR?
In the SKF Rolling Bearings catalogue this size is listed as 61902-2RZ — two low-friction non-contact elastomer seals, 15×28×7 mm per ISO 15. Quoted values: C 4.36 kN, C0 2.24 kN, Pu 0.095 kN, limiting speed 28000 r/min, mass 16 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61902-RSR.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.