W61902 bearing: complete specifications & equivalents
The W61902 is a ISO 15 radial bearing sized 15 x 28 x 7 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 15 mm |
| Outer diameter D | 28 mm |
| Width B | 7 mm |
| Material | SS440C |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 3.71 kN |
| Basic static load rating C0 | 2.24 kN |
| Fatigue load limit Pu | 0.095 kN |
| Reference speed (thermal) | 56000 rpm |
| Limiting speed (mechanical) | 34000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 14 g |
| Manufacturer designation | W 61902 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 0.591 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.276 in |
| ISO bore code | 02 |
| Radial section height (D−d)/2 | 6.5 mm |
| Smallest bore in 61900-series | 3 mm |
| Largest outer diameter in 61900-series | 1120 mm |
| Width range across 61900-series | 3–118 mm |
| Bore position in 61900-series (smallest first) | 10 of 63 |
| Bore above smallest 61900-series size | 12 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| W61902-2RS | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 15×28×7 mm envelope and equivalent catalogue ratings; W 61902-2RS1 is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| W61902-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 15×28×7 mm envelope and equivalent catalogue ratings; W 61902-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 61902 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 61902 shares the 15×28×7 mm envelope but carries different catalogue ratings (3.71/2.24 kN vs 4.36/2.24 kN) — the stainless execution is not a load-rating equivalent. |
| 61902-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 61902-2RS1 shares the 15×28×7 mm envelope but carries different catalogue ratings (3.71/2.24 kN vs 4.36/2.24 kN) — the stainless execution is not a load-rating equivalent. |
| 61902-RSR | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 61902-2RZ shares the 15×28×7 mm envelope but carries different catalogue ratings (3.71/2.24 kN vs 4.36/2.24 kN) — the stainless execution is not a load-rating equivalent. |
| 61902-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 61902-2Z shares the 15×28×7 mm envelope but carries different catalogue ratings (3.71/2.24 kN vs 4.36/2.24 kN) — the stainless execution is not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the W61902 model number is decoded
The W prefix denotes SKF stainless steel deep-groove bearings (X108CrMo17 / AISI 440C class rings). In the 61900-series, bore code 02 follows the 10/12/15/17 mm exception table, so 61902 fits a 15 mm shaft. Envelope 15×28×7 mm (0.591×1.102×0.276 in), C 3.71 kN, C0 2.24 kN, Pu 0.095 kN; limiting speed 34000 r/min and mass 14 g. The open W 61902 carries no shields or seals and relies on application lubrication and external sealing. Stainless is chosen for corrosion and washdown duty, not for extra load — the same-envelope chrome-steel bearing rates higher.
Typical equipment & failure modes
Common applications
- chemical and marine atmospheres
- medical and laboratory devices
- small pumps handling corrosive media
- bicycle and outdoor equipment
Known failure patterns
- surface staining and pitting when even the stainless steel is left unlubricated in salty or acidic duty
- seal and grease failure before the rings corrode in sustained washdown service
- contamination wear when the open arrangement is used without external seals
- lubricant starvation where no regreasing interval is maintained
Selection pitfalls — read before you substitute
- Corrosion resistance depends on clean, undamaged surfaces: never weld near W61902 or scratch the raceways during mounting, since the damaged spot starts corrosion.
- Temperatures above roughly 300 °C temper the stainless races; even standard greases fail far earlier — keep W61902 inside the quoted grease temperature range.
- W-prefix stainless rings (X108CrMo17 / AISI 440C class) resist moisture and weak chemicals but will still rust in chloride-rich or salt-spray duty without protection — W61902 is not marine-grade stainless.
- The stainless steel is martensitic and MAGNETIC; do not reject W61902 over magnetism — only austenitic grades are non-magnetic, and those are too soft for bearing raceways.
- Deep-groove geometry tolerates only minutes of misalignment; if the 28 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming W61902.
- Clearance suffixes follow the seal code in the designation stack (e.g. W 61902-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
Frequently asked questions
What are the dimensions of the stainless W61902?
SKF W 61902 measures 15×28×7 mm (0.591×1.102×0.276 in), about 14 g, C 3.71 kN.
What does the W in W 61902 mean?
W is the SKF prefix for stainless steel deep-groove bearings (rings in X108CrMo17 / AISI 440C class); the rest of the designation follows the normal series and bore rules.
Are W stainless bearings waterproof?
No — the stainless rings resist moisture and weak chemicals far better than 52100 chrome steel, but salt spray, strong chlorides and unlubricated washdown duty can still corrode W61902; add seals and food-grade grease for wet positions.
Can I replace a chrome-steel bearing with stainless W61902?
The envelope matches, but stainless rates lower (C 3.71 kN for W 61902); for corrosive environments that trade-off is intended, for high loads it shortens life.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.