61902-2RS-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61902-2RS-NTN model number is decoded

61902-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 15 by five gives the 15 mm bore; the 28 mm outside diameter and 7 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's contact-seal catalogue number is 6902LLU (suffix LLU, or LLH low-torque variant), mapped here from the industry-neutral -2RS spelling; the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 15 mm bore, induction heating to roughly 80–100 °C is the clean mounting method; never exceed 120 °C, and hold 61902 against the shaft shoulder while it cools so the ring cannot creep back.
• The 619xx thin section at 15 mm bore (6.5 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• Contact seals add drag and heat: 61902-2RS-NTN runs slower and cooler-limited than the open 61902; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Never wash a sealed 61902-2RS-NTN in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Measure the shaft, do not trust the drawing: a 15 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61902-2RS-NTN.
• NTN catalogues the contact-sealed version as 6902LLU (suffix LU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.
• At 15 mm bore the 61902 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• NTN rates 61902 at 16000 r/min grease limiting speed — this is an electric-motor range; keep the grease fill at 25–35% of the free bearing volume and avoid mixing grease thickener types if regreasing through the seal lip.
• At 4.05 kN dynamic load rating (C) and 2 kN static (C0), 0.16 kN fatigue load limit Cu, 61902 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 16 g, 61902 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×28×7 mm envelope of 61902 gives a D/d ratio of 1.87 and 6.5 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 4.05/2 kN load ratings, 0.16 kN fatigue load limit Cu NTN lists the grease limiting speed at 16000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 16 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6902LLU on the 15×28×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61902 in a rated drive.
• Order the C3 internal-clearance version (61902 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.