6207-ZZ-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6207-ZZ-FAG model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6207 carries bore code 07 = 35 mm. Outside diameter 72 mm and width 17 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 35 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. Schaeffler HR 1 catalogue order number: 6207-C-2Z (FAG suffix 2Z), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 35 mm shaft for 6207 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• The 62xx light series is the default general-purpose section at 35 mm bore; before upgrading to a 6307 for extra capacity, confirm the housing accepts a 72 mm OD and 17 mm width — it is not a drop-in swap.
• ZZ shields are non-contact: 6207-ZZ-FAG blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6207-2RS for that.
• Do not wash 6207-ZZ-FAG in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6207-ZZ-FAG-C3. No clearance suffix means normal CN clearance.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 17 mm-wide ring of 6207-ZZ-FAG drags the lip and overheats it.
• Schaeffler HR 1 lists the shielded version as 6207-C-2Z — FAG suffix 2Z, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the FAG order number when buying through a Schaeffler channel.
• FAG rates 6207 at 12700 r/min mechanical limiting speed (thermal reference speed 11300 r/min) — electric-motor territory; prefer the open or 2Z execution (sealed 2RSR variants lose roughly a third of the thermal speed) and confirm grease life at the reference speed for continuous running.
• The 35 mm bore puts 6207 in Schaeffler's general-purpose industrial range; the standard cage and CN clearance cover most electric-motor and pump duty, and FAG's X-life generation of these sizes carries higher ratings than legacy HR 1 printings — check the current eKatalog listing before reordering.
• At 28 kN dynamic load rating (C) and 15.4 kN static (C0), 6207 is a medium-load FAG bearing for most electric-motor and pump duty; check the static safety factor against C0 for preloaded or thrust-loaded arrangements.
• At 274 g, 6207 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 35×72×17 mm envelope of 6207 gives a D/d ratio of 2.06 and 18.5 mm radial section height — a heavy FAG section for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 28/15.4 kN load ratings, mass 274 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6207-C-2Z on the 35×72×17 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6207 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Schaeffler has moved many HR 1 sizes to the X-life generation with higher C/C0 ratings; the designation is unchanged, so a current eKatalog listing for 6207 may quote higher values than the HR 1 print figures on this page — the envelope is identical either way.
• FAG standard tolerance for this size is P0 (PN); P6/P5 precision executions exist for spindle-adjacent duty but carry different order numbers in the Schaeffler system — they are not a selectable sorting of standard stock.