6207-2RS bearing: complete specifications & equivalents
The 6207-2RS is a ISO 15 radial bearing sized 35 x 72 x 17 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 35 mm |
| Outer diameter D | 72 mm |
| Width B | 17 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 27 kN |
| Basic static load rating C0 | 15.3 kN |
| Fatigue load limit Pu | 0.655 kN |
| Limiting speed (mechanical) | 6300 rpm |
| Operating temperature | -30 to +110 °C |
| Mass | 300 g |
| Manufacturer designation | SKF 6207-2RSH |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 1.378 in |
|---|---|
| Outer diameter D | 2.835 in |
| Width B | 0.669 in |
| ISO bore code | 07 |
| Radial section height (D−d)/2 | 18.5 mm |
| Smallest bore in 6200-series | 3 mm |
| Largest outer diameter in 6200-series | 540 mm |
| Width range across 6200-series | 2.5–85 mm |
| Bore position in 6200-series (smallest first) | 16 of 45 |
| Bore above smallest 6200-series size | 32 mm |
Mounting, lubrication & life for 6207-2RS
Recommended fits & mounting
- Rotating inner ring on a 35 mm shaft: k5; housing bore H7 for normal stationary-load outer rings. Reverse the logic if the outer ring rotates.
- Fit by induction heating (max 120 °C) where practical — never drive the ring home through the rolling elements.
- Keep shaft and housing fillet radii below the bearing chamfer so the 17 mm-wide ring seats square on its shoulder.
Lubrication strategy
Contact-sealed execution: greased and sealed for life, no relubrication path. Grease life — not steel fatigue — usually sets the replacement interval; rising running temperature or noise near the end of service is the practical trigger.
Worked L10 life example (illustrative duty)
For ball bearings, L10h = (C/P)3 · 106 / (60·n). Taking an example radial equivalent load P = 3 kN at n = 1,500 r/min (a small belted motor duty — substitute the real equivalent load from the application calculation):
C = 27.0 kN → L10h ≈ 8,100 hours
Choosing a section at the same 35 mm bore
| Series | Open execution | OD × width | C (kN) | Limiting speed (r/min) |
|---|---|---|---|---|
| 60xx | 6007-FAG | 62 × 14 | 17.5 | 17,700 |
| 62xx | 6207-FAG | 72 × 17 | 28.0 | 15,000 |
| 63xx | 6307-FAG | 80 × 21 | 37.0 | 13,600 |
| 64xx | 6407-FAG | 100 × 25 | 56.0 | 9,500 |
| 618xx | 61807-FAG | 47 × 7 | 4.7 | 21,600 |
| 619xx | 61907-FAG | 55 × 10 | 10.9 | 17,800 |
| 160xx | 16007 | 62 × 9 | 12.3 | 16,700 |
A larger section is not a drop-in swap — OD and width change — and same-envelope seal variants are compared on the 35×72×17 envelope page. Match meaning, not the size chart alone: see what the cross-reference levels mean.
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6207-2RS-FAG | FAG | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6207-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 6207-ZZ-FAG | FAG | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
| 6207 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting. |
| 6207-2RS-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6207-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 6207-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs RSR) — confirm sealing suits the duty. |
| 6207-ZZ-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
| 6207-2RS-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6207-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 6207-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs RSR) — confirm sealing suits the duty. |
| 6207-ZZ-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×72×17 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
| 7207 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| NU207 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| W6207-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6207-2RS1 shares the 35×72×17 mm envelope but rates differently (27/15.3 kN vs 22.1/15.3 kN) — not a load-rating equivalent. |
| W6207-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6207-2Z shares the 35×72×17 mm envelope but rates differently (27/15.3 kN vs 22.1/15.3 kN) — not a load-rating equivalent. |
| W6207 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 6207 shares the 35×72×17 mm envelope but rates differently (27/15.3 kN vs 22.1/15.3 kN) — not a load-rating equivalent. |
| 207 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 207 shares the 35×72×17 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
| 207-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 207-2Z shares the 35×72×17 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6207-2RS model number is decoded
In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6207 carries bore code 07 = 35 mm. Outside diameter 72 mm and width 17 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 35 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. SKF's contact-seal catalogue number is 6207-2RSH (older text: -2RS1), mapped here from the industry-neutral -2RS spelling.
Typical equipment & failure modes
Common applications
- conveyors and drives
- agricultural equipment
- fans and blowers
- electric motors
Known failure patterns
- seal-lip hardening and loss of pre-grease in sustained high-temperature service
- grease-life expiry in the sealed-for-life cavity (no relubrication path)
- rolling-contact fatigue spalling after the rated L10 life is exceeded
- brinelling from static overload or hammering during mounting
Selection pitfalls — read before you substitute
- At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 6207-2RS; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
- The 62xx light series is the default general-purpose section at 35 mm bore; before upgrading to a 6307 for extra capacity, confirm the housing accepts a 72 mm OD and 17 mm width — it is not a drop-in swap.
- Contact seals add drag and heat: 6207-2RS runs slower and cooler-limited than the open 6207; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
- Never wash a sealed 6207-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
- Never mix components between two 6207-2RS units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
- Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
- SKF catalogues the contact-sealed version as 6207-2RSH (older printings may read -2RS1); it is shipped pre-greased and its 6300 r/min limiting speed is set by seal-lip drag and grease life versus the open bearing's 20000 r/min thermal reference speed. The single-seal catalogue number is 6207-RSH, used where one shaft side needs external relubrication.
- A one-seal execution 6207-RSH exists for arrangements that lubricate through the open side; fitting 6207-2RSH instead means lifetime grease and no external oil supply — mixing the two in the same shaft can starve the sealed position.
- The 27/15.3 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6207-2RS bearing?
A 6207-2RS deep-groove ball bearing has a 35 mm bore, 72 mm outer diameter and 17 mm width (1.378 × 2.835 × 0.669 in), per ISO 15 boundary dimensions. It is fitted with two contact rubber seals and is normally pre-greased.
What does the 2RS suffix on 6207-2RS mean?
2RS means two contact elastomer seals, one each side, usually over a lifetime grease fill. Sealing against dust and moisture is better than ZZ shields, but the lip drag lowers the speed and temperature ceiling.
How does the 6200 compare with other series at the same 35 mm bore?
The '2' is the light diameter series: 72×17 mm with an 18.5 mm radial section at 35 mm bore. A 6307 on the same bore is larger and higher-rated; a 6007 is smaller and lower-rated.
Are 6207 bearings from different brands interchangeable?
For boundary dimensions, yes: every brand's 6207 uses the same ISO 15 envelope (35×72×17 mm). Load ratings, limiting speeds, clearance, precision class and sealing design can differ, so verify those in the supplier catalogue when substituting. Seal suffixes also differ by brand (2RS, DDU, LLU, 2RSL and similar).
What is the SKF designation and catalogue data for 6207-2RS?
In the SKF Rolling Bearings catalogue this size is listed as 6207-2RSH — two contact elastomer seals over a lifetime grease fill, 35×72×17 mm per ISO 15. Quoted values: C 27 kN, C0 15.3 kN, Pu 0.655 kN, limiting speed 6300 r/min, mass 300 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 6207-2RS.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.